Решено Data ONTAP API Failed

Engineer

Активный участник
Доброго времени суток. Обновил версию ONTAP в контроллерах СХД FAS 2650 с версии 9.2 до версии 9.3. Все прошло удачно но после этого не могу добавить новый образ с ontap 9.4
Пример ошибки
Код:
Reason: Data ONTAP API Failed: Data retrieval failed from remote host "http://iis/94_q_nodar_image.tgz". Reason: Timeout was reached : Connection timed out after 60001 milliseconds
Если открыть ссылку в браузере то файл скачивается и доступен. Помогите:vsepomerlo:
 
Последнее редактирование модератором:
ping есть с контроллеров до FTP или http?
 
Пример использования на всякий
Код:
 cluster1::> network ping -node xena -destination 10.98.16.164 (network ping) 10.98.16.164 is alive
 
Доброго времени суток. Обновил версию ONTAP в контроллерах СХД FAS 2650 с версии 9.2 до версии 9.3. Все прошло удачно но после этого не могу добавить новый образ с ontap 9.4
Пример ошибки
Код:
Reason: Data ONTAP API Failed: Data retrieval failed from remote host "http://iis/94_q_nodar_image.tgz". Reason: Timeout was reached : Connection timed out after 60001 milliseconds
Если открыть ссылку в браузере то файл скачивается и доступен. Помогите:vsepomerlo:

Брандмауэр файервол внтивирус или межсетевой экран не блокируют соединение?
 
странно. пинг до шлюза есть. а до серверов с источником образа Ontap нету:upset:. Как импортировать образ через CLI ?
 
нет все открыто, ноды нетапа и сервер с образом в одной подсети
 
Можно так, но какая разница. Вам надо с сетевой проблемой разобраться
Код:
netapp> system node <жмем enter>
netapp> image package get URL
 
Нашел в Event Log
Код:
Event:
netinet.ethr.duplct.ipAdrr: Duplicate IP address 172.29.1.2!! sent from Ethernet address: 00:50:56:a3:ba:71.
Message Name:
netinet.ethr.duplct.ipAdrr
Sequence Number:
52963
Description:
This message occurs when another system is detected using an IP address configured on this system.
Action:
The Ethernet address uniquely identifies the other system that is using the IP address. If you are using static IP addresses, change the IP address configured on one of the systems. If DHCP is in use on the network, ensure that the static IP address is not in the range being used by the DHCP server.

Код:
Event:
ses.inconsistent.config: Inconsistent configuration detected for shelf connected to adapter 0b.
Message Name:
ses.inconsistent.config
Sequence Number:
42283
Description:
This message occurs when the system detects an inconsistent configuration of shelf-to-channel connections. One or more shelves on the reported channel are connected to a different set of channels (adapter ports or switch ports) than other shelves in the stack.
Action:
Verify that all cables are fully inserted on the storage shelves connected to the channel. Verify that the shelves are cabled so that all shelves in a stack are connected to the same channels.
 
частично разобрался, прописан ненужный маршрут по умолчанию в ontap. Пришлось удалить. Теперь осталось разобраться с DHCP
 
Добавил образ ontap через другой сервер. Теперь не проходит валидацию перед обновлением.
Warning: "DNS" is present as one of the sources in one or more ns-switch databases but no valid DNS configuration was
found for Vserver "ESXi". Remove "DNS" from ns-switch using the "vserver services name-service ns-switch"
command. Configuring "DNS" as a source in the ns-switch setting when there is no valid configuration can cause
protocol access issues.
Подскажите что означает это предупреждение???
 
Добавил образ ontap через другой сервер. Теперь не проходит валидацию перед обновлением.

Подскажите что означает это предупреждение???

удали настройки DNS в свойствах vserver
Remove "DNS" from ns-switch using the "vserver services name-service ns-switch"
 
да, спасибо. Я обновился вчера до последнего релиза. Можно вопрос закрывать
 
Назад
Верх Низ