обновление firmware VNX8000

Engineer

Активный участник
кто нибудь обновлял когда нибудь прошивку в системе хранения vnx8000 ? интересует совместимость версий, с какой на какую можно обновиться. если кто знает где посмотреть таблицу совместимости прошивок прошу подсказать..
 
кто нибудь обновлял когда нибудь прошивку в системе хранения vnx8000 ? интересует совместимость версий, с какой на какую можно обновиться. если кто знает где посмотреть таблицу совместимости прошивок прошу подсказать..
VNX5100

VNX5200

VNX5300

VNX5400

VNX5500

VNX5600

VNX5700

VNX5800

VNX5150

VNX7500

VNX7600

VNX8000

VNX-F5000

VNX-F7000

VNX2 Series

VNX1 Series

VNX-VSS100
все это семейство обновляется одинаково. Block OE Upgrades
  • The software packages required for this procedure will be the CX5-Bundle-05.3x.000.5.xxx.pbu file (if you are updating the VNX OE for Block), and any enablers that you are to install.
  • If you are upgrading VNX Block OE from R31 to R32 or R32 to R32 disable FASTVP prior to starting the NDU. See emc318603 for more information and steps for disabling FASTVP.
  • Select Express Install or Custom Install. (Express Install is offered if software was pre-staged using the Prepare for Installation option within the last 2 days.)
  • Diagnostic Tools and Offline Upgrade Options
  • Check the box labeled Allow Installation of Diagnostic Tools on SPs if the customer permits this.
This utility (1) checks if there is an active session on the SP, and (2) monitors the processor utilization and offers steps to reduce it if it is too high to allow the NDU to take place. These steps are based on the recommendations in emc211113. You can choose to perform any, all, or none of the steps. If the utilization drops to a satisfactory level after a task has been run, then the remaining steps are skipped. Any change made will be reset at the end of the NDU.
The utility is removed from the SPs at the end of the NDU. Disruptive Upgrades
  • A box labeled Enable Offline Upgrade is shown.
If you check this box, then both SPs will be rebooted at the same time. Select this option only if the customer has arranged for all attached hosts to be off-line. This procedure must only be done when all hosts I/O to the array has been halted since both SPs will be rebooted at the same time.
  • Offline Upgrade warning
Do you want to perform a disruptive upgrade?
  • If yes, click on Yes. A disruptive upgrade will be performed
  • If no, ckick in No. A disruptive upgrade will NOT be performed.
  • Browse to the software that is to be installed and select it.
  • Follow the wizard steps until you get to the Rules Checking screen.
Rules Checking


Did one of the rules fail?
  • If no, go to the next step.
  • If yes, details of the fault can be obtained by clicking on the fault icon for that rule. One of three options is presented for the rule. See the Software Installation Rules document for details of checks performed.
    • You can fix it if a fix icon appears to the right of the failed rule. Click on the fix icon and answer the prompt to override the rule.
    • If no fix icon is visible, hit alt and right-click on the “failed” icon. If it can be overridden, you will be shown an override button. Click on this icon.
    • If no fix icon is visible, and no override icon is shown when you hit alt and right-click on the failed icon, then the rule cannot be overridden. You will have to fix the fault before continuing.
After you have addressed or overridden the failed rule, it may be necessary to click on Rerun to rerun the rules if the Next button is grayed out. Finishing the upgrade

Follow the wizard steps to upgrade the software
 
кто нибудь обновлял когда нибудь прошивку в системе хранения vnx8000 ? интересует совместимость версий, с какой на какую можно обновиться. если кто знает где посмотреть таблицу совместимости прошивок прошу подсказать..

скинул ликбез на почту тебе:sndmail:
 
Назад
Верх Низ