Решено замена батарейки в RAID smart HPe DL 560 g9

deadushka

Участник
Добрый день! Подскажите как поменять батарейку в raid контроллере сервера HPe Proliant DL 560 g9 и не потерять данных ?
Батарейка для кэш представляет собой вот такую штуку:
333332.jpg
 
Последнее редактирование модератором:
Если кратко - выключаешь сервер, отключаешь питание, достаешь и меняешь батарейку. Потом включаешь.

Removing HP Smart Storage Battery​

To remove the component follow the steps given below:
  1. Power down the server.
  2. Remove the power from the server:
    1. Disconnect the power cord from the power source.
    2. Disconnect the power cord from the server.
  3. Do one of the following:
    1. Extend the server from the rack.
    2. Remove the server from the rack.
  4. Remove the access panel.
  5. Remove the fan cage.
  6. Disconnect the battery cable.
    c04723421.gif
  7. Remove the HP Smart Storage battery.
    c04723422.gif

Replacing HP Smart Storage Battery​

To replace the component follow the steps given below:
  1. Replace the HP Smart Storage battery.
  2. Connect the battery cable.
  3. Replace the fan cage.
  4. Replace the access panel.
  5. Do one of the following:
    1. Extend the server into the rack.
    2. Replace the server into the rack.
  6. Replace the power to the server:
    1. Connect the power cord to the server.
    2. Connect the power cord to the power source.
  7. Power up the server.
 
Если кратко - выключаешь сервер, отключаешь питание, достаешь и меняешь батарейку. Потом включаешь.

Removing HP Smart Storage Battery​

To remove the component follow the steps given below:
  1. Power down the server.
  2. Remove the power from the server:
    1. Disconnect the power cord from the power source.
    2. Disconnect the power cord from the server.
  3. Do one of the following:
    1. Extend the server from the rack.
    2. Remove the server from the rack.
  4. Remove the access panel.
  5. Remove the fan cage.
  6. Disconnect the battery cable.
    c04723421.gif
  7. Remove the HP Smart Storage battery.
    c04723422.gif

Replacing HP Smart Storage Battery​

To replace the component follow the steps given below:
  1. Replace the HP Smart Storage battery.
  2. Connect the battery cable.
  3. Replace the fan cage.
  4. Replace the access panel.
  5. Do one of the following:
    1. Extend the server into the rack.
    2. Replace the server into the rack.
  6. Replace the power to the server:
    1. Connect the power cord to the server.
    2. Connect the power cord to the power source.
  7. Power up the server.
Спасибо! Попробовал выключить сервер через удаленный рабочий стол. Сразу на почту пришли подозрительные ошибки от iLO:

EVENT (26 Jan 15:17): Unrecoverable System Error (NMI) has occurred. System Firmware will log additional details in a separate IML entry if possible
Integrated Management Log Severity: CRITICAL

EVENT (26 Jan 15:17): Uncorrectable PCI Express Error (Embedded device, Bus 0, Device 0, Function 0, Error status 0x00000000)
Integrated Management Log Severity: CRITICAL
Сервер в общем через мягкое обычное выключение не выключился. Пришлось отключать через жесткое нажатие по питанию.
Батарейку поменял, все завелось без проблем - ошибки исчезли. Спасибо!
 
Назад
Верх Низ